IN STOCK & SHIPS FAST!
1995-2002 Range Rover P38A Chassis 4-Wheel Suspension Conversion Kit With 2" Lift And 4 Shocks (LB24FL)
Monday - Friday: 8 AM - 9 PM
Saturday: 9 AM - 6 PM
- Why Strutmasters
- OEM Numbers
Convert Your Air Suspension To A Coil Spring Suspension. End Your Air Suspension Problems Forever...Strutmasters 1995-2002 Range Rover P38A Chassis 4 Wheel Air Suspension Conversion Kit w/ 2" Lift and Front & Rear Shocks is the perfect solution to your air suspension problems. Designed to be very affordable, you can convert your air suspension to use standard shocks/struts and coil springs for less than the price of replacing one air strut.
Conversion Kit Features
- Saves Money
- All New Components
- 2" Lift Returns Vehicle to "Raised" Factory Suspension Setting.Provides Additional Clearance For Off-Roading,Or For Oversize Wheels And Tires
- More Reliable Than Air Suspensions
- No Modifications Required To Install
- Easy To Install
- Premium Springs
Air Suspension Conversion Kit Includes
- 2 Front Springs
- 2 Premium Front Shocks
- 2 Rear Springs
- 2 Premium Rear Shocks
- (4) 2" Lift Blocks
- All Necessary Mounts
- All Necessary Hardware
- Detailed Instructions Including How To Disable The Suspension Warning Light
This Conversion Kit Fits1995 Range Rover P38a Chassis, 1996 Range Rover P38a Chassis, 1997 Range Rover P38a Chassis , 1998 Range Rover P38a Chassis , 1999 Range Rover P38a Chassis, 2000 Range Rover P38a Chassis, 2001 Range Rover P38a Chassis, 2002 Range Rover P38a Chassis
- Fits Range Rover P38a Chassis Only
The 1995-2002 Range Rover P38A Chassis is built with the following suspension components:
1995-2002 Range Rover P38A Chassis Shock Absorbers (x4)- a metal tubing filled with gas-charged hydraulic fluid that is connected to the wheel of a vehicle in order to reduce the effects of vertical travel on a rough surface which controls the bounciness, and therefore comfort, of a vehicle.
1995-2002 Range Rover P38A Chassis Air Struts (x4)- struts that contain an air bladder whose dampening capabilities is controlled by the suspension control module; these have two functions. They connect the wheel of a vehicle to the driving surface in order to reduce the effects of vertical travel on a rough surface which controls the bounciness, and therefore comfort, of a vehicle. They also help maintain the vehicles correct ride height, especially whenever the amount of load put onto the vehicle changes.
1995-2002 Range Rover P38A Chassis Height Sensors (x4)- a linkage located near each wheel of a vehicle with any electronic suspension that, either mechanically or electronically, constantly measures the height of the vehicle, and reports this information back to the control module so that the computer can identify if changes in height need to be adjusted accordingly. The ride height sensor is a moving part, and like all moving parts, they will eventually wear out.
1995-2002 Range Rover P38A Chassis Air Lines- tubes that run from a compressor (air suspension) to the air struts which carry pressurized air to the air bags components in order to adjust the height of the vehicle, respectively.
1995-2002 Range Rover P38A Chassis Solenoids (x4)- usually L-shaped, these plastic components connect the electrical connection and lines of suspension components to the suspension control module on vehicles with active suspension. The solenoid regulates the air pressure for each air spring. Solenoids start to leak as they wear out causing the vehicle to sag or to lean. This will cause the ride height sensor to send a signal to activate the compressor in an attempt to inflate the air suspension and level out the vehicle. This excessive work load will eventually lead to total failure of the compressor.
1995-2002 Range Rover P38A Chassis Compressor- creates/sends pressurized to active suspension components. When the air suspension starts leaking, the compressor/pump starts working harder to try to keep the system inflated. By the time air suspension leaks down completely, sitting the vehicle on its tires, the compressor will either have failed or be well on its way to full failure. Buying replacement struts and taking the time to install them only to find out the compressor still needs to be replaced can be very frustrating, time-consuming, and expensive.
1995-2002 Range Rover P38A Chassis Dryer Assembly- used to keep moisture out of air lines and air springs in order to prevent freezing and internal cracking of these parts. Once air suspension starts leaking, moisture will build-up throughout the air system. Moisture damages the air suspension from the inside. The dryer will need to be replaced in order to eliminate the moisture and prevent any further damage.
1995-2002 Range Rover P38A Chassis Suspension Control Module- a computer which is responsible for the operations of the air suspension system and maintaining the vehicles correct ride height.
1995-2002 Range Rover P38A Chassis O-rings- Although they are the least expensive parts of the air suspension, they are responsible for maintaining the seal where all of the air lines connect. Be sure to replace the O-rings when repairing any air suspension system.
Suspension Failure Signs
If the 1995-2002 Range Rover P38A Chassis is not reaching and maintaining the proper ride height, it may have a failed or leaking air suspension system. Look for a suddenly noticeable height variance between different sides of the P38A. This may look like one sagging end, one inflated end, a ‚Äúsquatting down‚Äù appearance, or a shifting lean from side to side. Other classic signs to look for include an improperly working air compressor and an illuminated suspension warning light on the instrument cluster. The longer the Chassis owner postpones a repair, the more expensive it is. Any suspension issue should be fixed as soon as it presents itself.